Lubricating Your Airsoft Gun


Likewise with gun support, airsoft firearms also need a TLC every once in a while, and the motivation behind this blog is to teach you – the airsoft fan – concerning when and how this upkeep ought to happen.

In the first place, to clear up a typical misinterpretation… airsoft weapons are NOT to be greased up with WD-40 or firearm oil. The appropriate ointment for airsoft firearms is high grade silicone oil. (I for one utilize Premium P-Force airsoft silicone execution grease in a shower bottle). Whatever else will draw in particles and soil, foul your barrel and internals, and make destructive harm your airsoft weapon. Use silicone oil splash solely.

Cleaning The Barrel:

Airsoft firearm barrels truly do 45 colt ammo should be cleaned, and a sign of ‘with regards to when’ lies in the flight-way of your airsoft weapon BBs. On the off chance that the airsoft pellet is digressing upward, now is the right time to recover your cleaning pole and a little piece of value paper towel which you’ll string through the tip of the bar (as you would string through a needle – the portion of the paper towel ought to be roughly ½” wide by 3″ long), and get your silicon oil. Daintily splash the strip, and afterward embed the cleaning bar strip-first into the barrel, turning the pole as you delicately drop it first down the length of the barrel, and afterward back out. Following this, string a perfect piece of paper towel into the tip of the cleaning bar and rehash the method (this will eliminate any overabundance silicon oil from the barrel, and leave it impediment free).

Greasing up the Hop Up and Gearbox:

For issues with airsoft AEGS mis-taking care of or sticking, sometimes an airsoft firearm’s bounce up should be greased up. To do this, eliminate the weapon’s magazine and shoot a few times in self-loader to guarantee that the jump up is liberated from airsoft BBs, and afterward put the firearm on your lap, topsy turvy. With your container of silicon oil, point the jug and going with shower tube (which you’ve previously embedded into the jug’s spout) into the jump up, and splash one to twice. Be saving with the oil (you would rather not use excessively), and let the weapon sit for five minutes, permitting the silicone to saturate the bounce up.

Similarly as with the jump up, your gearbox may once in a while should be greased up too (albeit considering that gearboxes comes from their particular producers loaded with modern grade oil or white lithium, this kind of support seldom should be performed. Assuming that your gearbox is crying, this may anyway get the job done). To grease up the gearbox, the engine will initially should be eliminated from the airsoft electric firearm, and when that undertaking is finished, a little opening in the lower part of the gearbox will be noticeable by looking into the now-empty weapon handle. Place the tip of the shower tube through the handle and just into the apparent gearbox opening, and splash three to multiple times. Once more, leave the AEG topsy turvy to permit the silicon oil to work its direction into the airsoft gearbox.

Greasing up Gas and C02 Airsoft Guns:

Silicone oil is a required extra for gas and c02 airsoft firearms, especially of the blowback assortment. As gas airsoft magazines depend on elastic gaskets and O-rings to perform, they need to frequently be greased up with silicone oil to hold the gasket’s extension, which will help the gas firearm in appropriately working (and which will hold the gas back from venting or delivering rashly). To grease up a gas mag, splash silicone oil into the port at the highest point of the mag, and afterward work the valve as an afterthought this way and that for roughly one moment. This system will permit the oil to leak down onto the gasket. Greasing up the gas mag’s fill port on the lower part of the magazine ought to likewise be directed. To do as such, hold the magazine topsy turvy, and embedding the tip of the splash tube into the fill port, shower one to twice. Permit the oil to work its direction into the fill-port gasket by leaving the mag topsy turvy for five minutes or so prior to stacking the mag with gas and testing.

c02 airsoft weapons and mags periodically should be greased up too. Utilizing the splash bottle, grease up the mag’s gasket where it comes into contact with the c02 chamber (for c02 firearms where the chamber is embedded straightforwardly into the weapon’s single handed grip, correspondingly grease up the gasket which comes into contact with the chamber). You’ll need to stand by at least ten minutes prior to testing, as anything earlier will keep the oil from working its direction really into the elastic seals (c02 is cold and will make the oil become thick).

The slide rails of the two gas and c02 airsoft blowback weapons may once in a while should be greased up too, to consider legitimate slide crossing. To do as such, eliminate the slide, and gently splash all contact focuses between the slide and the firearm body, and afterward reattach the slide. This will give legitimate oil and permit to a climate almost absent any trace of grinding.

Mike Zhang is the President and COO of Airsoft Megastore, an airsoft retailer offering electric and internal combustion airsoft weapons. Kindly visit Airsoft Megastore to search for airsoft green gas weapons and full metal airsoft rifles for players of any experience level.


Leave a Reply

Your email address will not be published. Required fields are marked *